|
|
|
0 members (),
162
guests, and
17
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
There are no members with birthdays on this day. |
#3530
Fri 22 Oct 2004 06:44:PM
|
Joined: Oct 2004
Posts: 1
Space Trainee
|
OP
Space Trainee
Joined: Oct 2004
Posts: 1 |
I am trying to pick up Optus B3 satellite in Sydney but i am not sure what elevation to set the dish to.It is 90cm offset dish. There is an indicator at the back of the dish that shows the elevation in degrees. I set that angle to 50 degrees but it didnt help. Can anyone tel me what to set up the indicator to?<br /><br />I have set up the LNB to 43 degrees, Is this correct?<br /><br />One last question. What Frequency should i set the LNB to?.The range of the frequency is 12.25-12.75 GH with local oscilator of 11.3GHz<br /><br />I appreicate it if anyone gets back to me<br /><br />Thanks
|
|
CMS The Best Conveyancing solicitors conveyancing quotes throughout the UK
For any webhosting enquiries please email webmaster@aus-city.com
|
#3531
Sat 23 Oct 2004 04:01:AM
|
Joined: Feb 2001
Posts: 381,904
Launch Director
|
|
Launch Director
Joined: Feb 2001
Posts: 381,904 |
In Sydney if you set it roughly to 50 degrees your pretty close.<br /><br />Hope that helps!
|
|
#3532
Mon 13 Dec 2004 01:03:AM
|
Joined: Dec 2004
Posts: 1
Space Trainee
|
|
Space Trainee
Joined: Dec 2004
Posts: 1 |
set it to 11300 ( lnb )<br /> and try 45 degrees
|
|
#3533
Mon 13 Dec 2004 02:34:AM
|
Joined: Nov 2004
Posts: 19
Space Cadet
|
|
Space Cadet
Joined: Nov 2004
Posts: 19 |
Heya - In wonder if someone can help me out here.<br /><br />I've got a working TARBS (yes, the stock standard ones) BOX. I've been reading that with a FTA digital receiver I can get the FTA channels that were under TARBS before.. here's how I went:<br /><br />1. powered up HUMAX (VA-ACE) unit, operationally looks AOK.<br /><br />2. removed sat cable from working TARBS box (note, dish already re-aligned) and insert into HUMAX box 3. configure following parameters on HUMAX box (identical from working TARBS box).<br /> - LNB 11300<br /> - Transponder Freq 12640<br /> - Symbol Table 22500<br /> - 22K Tone off<br /> - Polariz: H<br /> - FEC: Auto Detect<br /><br />On HUMAX box, I am getting a SIGNAL LEVEL of 85 (on old TARBS-box was about 70). <br /><br />On HUMAX box, I am getting a SIG QUALITY of ZERO (0) however.... This was about 57 on the working box.<br /><br />Here-in lies my problem.<br /><br />I attempted a clean sweep scan but still nothing.<br /><br />My objective was to get 2 units in the house working, but am tripping at getting the new one working. <br /><br />Can anyone advise me where I am going wrong.<br /><br />Thanks In Advance!
|
|
#3534
Wed 15 Dec 2004 02:03:PM
|
Joined: Nov 2004
Posts: 19
Space Cadet
|
|
Space Cadet
Joined: Nov 2004
Posts: 19 |
its ok, been fixed. put all settings to AUTO and only set the LNB to 11300, and whallah! thanks anyway :-)
|
|
|
Forums60
Topics713,002
Posts747,618
Members2,957
| |
Most Online4,158
Jun 21st, 2024
|
|
|
|
|
Copyright 1996 - 2024 by David Cottle. Designed by David Bate Jr. All Rights Reserved.
By using this forum, the user agrees not to transfer any data or technical information received under the agreement, to any other entity without the express approval of the AUS-CITY Forum Admins and/or authors of individual posts (Forum Admins and DoD/USSPACECOM for the analysis of satellite tracking data).
Two-line elements (TLE) and all other satellite data presented and distributed via this forum and e-mail lists of AUS-CITY are distributed with permission from DoD/USSTRATCOM.
Reprise Hosting
|
|
